Unable to see Adaptec AIC 7880 controller on Tru64 V5.1

Unable to see Adaptec AIC 7880 controller on Tru64 V5.1

Post by onlin » Wed, 04 Feb 2004 14:55:07


i,

I hope I am not asking a question which has been asked, I have
searched the web top to bottom before posting.

I am trying to install an Adaptec AIC 7880 SCSI controller in a DS10
running Tru64 V5.1. I can see the controller and it is identified via
SRM with >>> show config

Also it shows the six disks connected via a StorageWorks disk cabinet.
However, I am unable to get Tru64 to recognise this controller.

Below is the output I am receiving in /var/adm/messages. Any help
would be greatly apprecited, I am starting to bang my head on the
case...

-Dougal

Feb 2 15:24:05 quscs1 vmunix: Alpha boot: available memory from
0x19f2000 to 0x1ff2e000
Feb 2 15:24:05 quscs1 vmunix: Compaq Tru64 UNIX V5.1 (Rev. 732); Thu
Aug 24 23:17:34 EDT 2000
Feb 2 15:24:05 quscs1 vmunix: physical memory = 512.00 megabytes.
Feb 2 15:24:05 quscs1 vmunix: available memory = 485.23 megabytes.
Feb 2 15:24:05 quscs1 vmunix: using 1903 buffers containing 14.86
megabytes of memory
Feb 2 15:24:05 quscs1 vmunix: Firmware revision: 6.4-9
Feb 2 15:24:05 quscs1 vmunix: PALcode: UNIX version 1.91-72
Feb 2 15:24:05 quscs1 vmunix: AlphaServer DS10 466 MHz
Feb 2 15:24:05 quscs1 vmunix: PCI device at bus 0, slot 16, function
0 could not be configured:
Feb 2 15:24:05 quscs1 vmunix: Vendor ID 0x9004, Device ID 0x8178,
Base class 0x1, Sub class 0x0 Sub-VID 0x9004 Sub-DID 0x7881
Feb 2 15:24:05 quscs1 vmunix: has no matching entry in the PCI
option table
Feb 2 15:24:05 quscs1 vmunix: pci0 (primary bus:0) at nexus
Feb 2 15:24:05 quscs1 vmunix: isa0 at pci0
Feb 2 15:24:05 quscs1 vmunix: gpc0 at isa0
Feb 2 15:24:05 quscs1 vmunix: gpc1 not probed
Feb 2 15:24:05 quscs1 vmunix: ace0 at isa0
Feb 2 15:24:05 quscs1 vmunix: ace1 at isa0
Feb 2 15:24:06 quscs1 vmunix: lp0 at isa0
Feb 2 15:24:06 quscs1 vmunix: fdi0 at isa0
Feb 2 15:24:06 quscs1 vmunix: fd0 at fdi0 unit 0
Feb 2 15:24:06 quscs1 vmunix: tu0: DECchip 21143: Revision: 4.1
Feb 2 15:24:06 quscs1 vmunix: tu0: auto negotiation capable device
Feb 2 15:24:06 quscs1 vmunix: tu0 at pci0 slot 9
Feb 2 15:24:06 quscs1 vmunix: tu0: DEC TULIP (10/100) Ethernet
Interface, hardware address: 00-10-64-30-24-3F
Feb 2 15:24:06 quscs1 vmunix: tu0: auto negotiation off: selecting
10BaseT (UTP) port: half duplex
Feb 2 15:24:06 quscs1 vmunix: tu1: DECchip 21143: Revision: 4.1
Feb 2 15:24:06 quscs1 vmunix: tu1: auto negotiation capable device
Feb 2 15:24:06 quscs1 vmunix: tu1 at pci0 slot 11
Feb 2 15:24:06 quscs1 vmunix: tu1: DEC TULIP (10/100) Ethernet
Interface, hardware address: 00-10-64-30-24-3E
Feb 2 15:24:06 quscs1 vmunix: tu1: auto negotiation off: selecting
10BaseT (UTP) port: half duplex
Feb 2 15:24:06 quscs1 vmunix: ata0 at pci0 slot 13
Feb 2 15:24:06 quscs1 vmunix: ata0: ACER M1543C
Feb 2 15:24:06 quscs1 vmunix: scsi0 at ata0 slot 0 rad 0
Feb 2 15:24:06 quscs1 vmunix: scsi1 at ata0 slot 1 rad 0
Feb 2 15:24:06 quscs1 vmunix: comet0: Card type 'Elsa GLoria' with
8MB framebuffer memory.
Feb 2 15:24:06 quscs1 vmunix: comet0 at pci0 slot 14
Feb 2 15:24:06 quscs1 vmunix: isp0 at pci0 slot 15
Feb 2 15:24:06 quscs1 vmunix: isp0: QLOGIC ISP1040B/V2
Feb 2 15:24:06 quscs1 vmunix: isp0: Firmware revision 5.57 (loaded by
console)
Feb 2 15:24:06 quscs1 vmunix: isp0: Fast RAM timing enabled.
Feb 2 15:24:06 quscs1 vmunix: scsi2 at isp0 slot 0 rad 0
Feb 2 15:24:06 quscs1 vmunix: Created FRU table binary error log
packet
Feb 2 15:24:06