[SATA] Disabling irq: #11 with silicon image 3112 sata controller with sata_sil and libata (NO RAID)

[SATA] Disabling irq: #11 with silicon image 3112 sata controller with sata_sil and libata (NO RAID)

Post by Helge Pomo » Wed, 25 May 2005 06:50:11

hm,
now i realise it that ive answered last message not sended new...
sorry about that... well again:

i want to install my root fs on my primary sata drive, its solo
plugged at the onboard controller atm. (at the point it works fine,
with 2.6.5...)

-disabling acpi (no changes)
-disabling irq debug (no changes)
-change compatible mode (well bios option misses)
-disabling sata (well i want use it so disabling isnt that i want to know...)

well so heres my previous message i did send couple of minutes ago:

Hi there,
Got similar looking problem here,
i cant change sata modes or something alike...

I get *disabling irq* message with Intel ICH 4 / SIL 3112 A rev 01
SATA Controller on Asus P4G8X Deluxe board (P4 Northwood, Intel
*granite bay* E702 Chipsets) at distros which using newer kernel than
2.6.5, manual installation of kernel >= 2.6.7 fails
(well i think udev isnt creating devices or something cause after i
did try compile the kernel on my own etc...
kernel modules found the sata controller, the devices and the
partitions, but hangsup with an *waiting for /dev/sda3 (my root disk)
to appear*)

my messages are known i think... but for completion:
(i did copied it from net this isn exactly my error
cause i dont know how to copy the error, after failed boot...)
ata1: SATA max UDMA/100 cmd 0xE09FC080 ctl 0xE09FC08A bmdma 0xE09FC000
irq 11
ata2: SATA max UDMA/100 cmd 0xE09FC0C0 ctl 0xE09FC0CA bmdma
0xE09FC008 irq 11
irq 11: nobody cared!
[<c012fbea>] __report_bad_irq+0x2a/0x90
[<c012f5a0>] handle_IRQ_event+0x30/0x70
[<c012fcdc>] note_interrupt+0x6c/0xd0
[<c012f710>] __do_IRQ+0x130/0x160
[<c01042b9>] do_IRQ+0x19/0x30
[<c010289a>] common_interrupt+0x1a/0x20
[<c0117830>] __do_softirq+0x30/0x90
[<c01178b6>] do_softirq+0x26/0x30
[<c012f564>] irq_exit+0x34/0x40
[<c01042be>] do_IRQ+0x1e/0x30
[<c010289a>] common_interrupt+0x1a/0x20
[<c01005f0>] default_idle+0x0/0x30
[<c0100613>] default_idle+0x23/0x30
[<c010068a>] cpu_idle+0x3a/0x60
[<c03ca767>] start_kernel+0x147/0x160
[<c03ca360>] unknown_bootoption+0x0/0x1b0
handlers:
[<c0273770>] (usb_hcd_irq+0x0/0x70)
[<e0a65460>] (ata_interrupt+0x0/0x1c0 [libata])
/*
the handlers differs from my messages i get also reported:
[ohci1394]
[reiserfs]
[usbcore]
[sata_sil]
/*
Disabling IRQ #11
ata1: dev 0 cfg 49:2f00 82:346b 83:7f21 84:4003 85:3469 86:3c01
87:4003 88:203f
ata1: dev 0 ATA, max UDMA/100, 390721968 sectors: lba48

i got that problem after a new installation of my system, before that
it worked with a 2.6.10 kernel on same system (something about 4 weeks
ago dont know settings anymore sorry...)

well im trying some different partition style layouts,
cause i just get that message with an seperate boot partition formated
with ext3,
if i set up a blank installation without that */boot* it works fine,
even with newer version's...

if u got an idea, need some logs infos etc message me :-)

greets
Helge Pomorin
Berlin, Germany
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to XXXX@XXXXX.COM
More majordomo info at http://www.yqcomputer.com/
Please read the FAQ at http://www.yqcomputer.com/