AWE32

AWE32

Post by Bill » Sun, 21 Sep 2003 08:47:05


Can someone post the config sys lines for this card.
My install only has one line which refers to sbaud1$ which
isn't there.
This is a non-pnp awe32 which of course works fine in winblows 98.
Generic dma1 and 5 with irq 5 and the 220 etc addr.
This is a multiboot os machine, so is easy to check.

Any help would be appreciated

Bill Cook
 
 
 

AWE32

Post by Doug Fitzp » Sun, 21 Sep 2003 09:57:03


DEVICE=C:\MMOS2\SBAWED2.SYS /C:1 /D:1 /H:5 /I:5 /A:220 /M:330
/N:SBAUD1$ /Q /P /G
DEVICE=C:\MMOS2\AUDIOVDD.SYS SBAUD1$


--
Regards,
Doug

**** remove leading g for email replies. ****

 
 
 

AWE32

Post by Steven Lev » Sun, 21 Sep 2003 10:20:25

In <Ip5dQMbWjEcZ-pn2-Wuc17xklZbXW@localhost>, on 09/20/2003
at 12:57 AM, "Doug Fitzpatrick" < XXXX@XXXXX.COM > said:



For comparison:

DEVICE=F:\MMOS2\SBAWED2.SYS /C:1 /D:1 /H:5 /I:10 /A:220 /B:8 /M:330
/N:SBAUD1$ DEVICE=F:\MMOS2\AUDIOVDD.SYS SBAUD1$

Steven


--
--------------------------------------------------------------------------------------------
Steven Levine < XXXX@XXXXX.COM > MR2/ICE 2.37 #10183
Warp4/FP15/14.093c_W4 www.scoug.com irc.webbnet.info irc.fyrelizard.org #scoug (Wed 7pm PST)
--------------------------------------------------------------------------------------------
 
 
 

AWE32

Post by Steven Lev » Sun, 21 Sep 2003 10:22:16

In <bkg4i6$1hme5$ XXXX@XXXXX.COM >, on 09/19/2003
at 07:47 PM, Bill < XXXX@XXXXX.COM > said:


You might want to use mmcheck from:

http://www.yqcomputer.com/

to check mmpm2.ini.

Steven

--
--------------------------------------------------------------------------------------------
Steven Levine < XXXX@XXXXX.COM > MR2/ICE 2.37 #10183
Warp4/FP15/14.093c_W4 www.scoug.com irc.webbnet.info irc.fyrelizard.org #scoug (Wed 7pm PST)
--------------------------------------------------------------------------------------------
 
 
 

AWE32

Post by William L. » Sun, 21 Sep 2003 13:51:29

Sir:



It is a supported card with Warp 4, MCP/eCS. Use the System installer
(Selective Install) to set the switches. Make sure that it is installed
correctly by using mmcheck as previous suggested. If they both work
okay (no errors) and it still does not work, make sure that you have in
BIOS "PnP OS" set to no, for all operating systems. Assign (reserve)
the irq and both dma channels to legacy ISA cards. Then check that what
is assigned in Windows is to what you set the switches by selective
install for OS/2 and that both agree with the jumpers on the card.
--
Bill
Thanks a Million!
 
 
 

AWE32

Post by Doug Fitzp » Sun, 21 Sep 2003 15:11:50

On Sat, 20 Sep 2003 01:20:25 UTC, Steven Levine



Can you recall what the B:8 does?

--
Regards,
Doug

**** remove leading g for email replies. ****
 
 
 

AWE32

Post by Steven Lev » Mon, 22 Sep 2003 00:56:08

In <Ip5dQMbWjEcZ-pn2-keDGjwttquOP@localhost>, on 09/20/2003
at 06:11 AM, "Doug Fitzpatrick" < XXXX@XXXXX.COM > said:



It sets the DMA buffer count. I'm not sure what the default is.

Steven


--
--------------------------------------------------------------------------------------------
Steven Levine < XXXX@XXXXX.COM > MR2/ICE 2.37 #10183
Warp4/FP15/14.093c_W4 www.scoug.com irc.webbnet.info irc.fyrelizard.org #scoug (Wed 7pm PST)
--------------------------------------------------------------------------------------------
 
 
 

AWE32

Post by Klaus Stae » Mon, 22 Sep 2003 01:08:55


default is 8 ;-) (so no need to apply that), range is from 1-24, but
using default is recommended.

Klaus Staedtler